.. Déformation-plastique-en-usinage, 25 4.1. Zone de cisaillement primaire, p.29

.. Contact-À-l-'interface-outil-copeau, 32 5.1. Température à l'interface outil, p.35

A. Usure-par, 40 1.3. Usure par adhésion : arête rapportée et attrition, p.41

.. Caractérisation-de-l-'endommagement-en-perçage-À-sec-de-l-'aa2024-t351, 51 4.1. Perçage et dispositif expérimental, p.51

.. Géométrie-du-copeau,-vitesse-du-copeau-et-vitesse-de-glissement, 59 1.2, p.60

.. Principe-du-modèle-inverse, 82 2.2. Identification du modèle, p.83

.. Simulation-numérique, 86 3.1. Simulation numérique du procédé d'enlèvement de matière, ., p.88

.. Endommagement-des-outils-À-faible-vitesse-de-coupe-et-petite-avance, 104 4.1. Formation de l'arête rapportée, p.105

.. Mécanismes-d-'endommagement-aux-conditions-de-coupe-sévères, 108 5.1. Formation d'une couche adhérente (ou couche de transfert)108 5.2. Diffusion, ., p.113

C. J. Andr_00, H. Andrewes, W. M. Feng, and . Lau, Machining of an aluminum/SiC composite using diamond inserts, Journal of Materials Processing Technology, vol.102, pp.25-29, 2000.

H. J. Antu_96, M. Antunez, and . Kleiber, Sensitivity Analysis of Metal Forming Processes Involving Frictional Contact in Steady State, Journal of Materials Processing Technology, vol.60, pp.485-491, 1996.

J. A. Arse_97 and . Arsecularatne, On Tool-Chip Interface Stress Distributions, Ploughing Force and Size Effect in Machining, International Journal of Machine Tools and Manufacture, vol.37, pp.885-899, 1997.

H. Ay_98 and . Ay, Heat transfer and life of metal cutting tools in turning, International Journal of Heat and Mass Transfer, vol.41, pp.613-623, 1998.

J. A. Bail_75 and . Bailey, Friction in metal machining. Mechanical aspects, pp.243-275, 1975.

N. Basu_96, V. K. Basu, and . Sarin, Oxidation behavior of WC-Co, Materials Science and Engineering: A, vol.209, issue.1-2, pp.206-212, 1996.
DOI : 10.1016/0921-5093(95)10145-4

J. Bata_02, H. Battaglia, L. Elmoussami, and . Puigsegur, Modélisation du comportement thermique d'un outil de fraisage : approche par identification de système non entier, C. R. Mecanique, vol.330, pp.857-864, 2002.

A. Batt_68, A. Battacharyya, and . Ghosh, Diffusion wear of cutting tools, Annals of C.I.R.P XVI, pp.369-375, 1968.

H. Bil_04, S. E. Bil, A. E. Kilic, and . Tekkaya, A comparison of orthogonal cutting data from experiments with three different finite element models, International Journal of Machining Tools and Manufacture, vol.44, pp.933-944, 2004.

G. Boot_61 and . Boothroyd, Temperatures in Orthogonal Metal Cutting, Proceedings of the Institution of Mechanical Engineers, vol.177, pp.789-802, 1961.

D. U. Brag_02, A. E. Braga, G. W. Diniz, N. L. Miranda, and . Coppini, Using a minimum quantity of lubricant (MQL) and a diamond coated tool in the drilling of aluminum???silicon alloys, Journal of Materials Processing Technology, vol.122, issue.1, pp.127-138, 2002.
DOI : 10.1016/S0924-0136(01)01249-3

J. Brio_93 and . Brion, Contribution à l'étude des mécanismes de formation de couches de transfert non métallique sur un outil en coupe continue d'aciers de décolletage à inclusions contrôlées, Thèse de Doctorat, Institut National Polytechnique de Lorraine, 1993.

O. Bruc_99, G. Brucelle, and . Bernhart, Methodology for service life increase of hot forging tools, Journal of Materials Processing Technology, vol.87, pp.237-246, 1999.

J. D. Camp_70, W. G. Campbell, and . Ferguson, The Temperature and Strain-rate Dependence of the Shear Strength of Mild Steel, Philosophical. Magazine, vol.21, pp.63-82, 1970.

A. Marcos and . Sem, EDS insight into the BUL and BUE differences in the turning process of AA2024 Al-Cu Alloy, International Journal of Machine Tools and Manufacture, vol.42, pp.215-220, 2002.

S. Casto_99, E. Lo-casto, E. Lo-valvo, S. Lucchini, M. Maschio et al., Ceramic materials wear mechanisms when cutting nickel-based alloys, pp.229-227, 1999.

C. H. Chandrasekaran and D. V. Kapoor, Photoelastic Analysis of Tool-Chip Interface Stresses, Journal of Engineering for Industry, vol.87, issue.4, pp.495-502, 1965.
DOI : 10.1115/1.3670869

C. B. Changeux, Loi de comportement pour l'usinage. Localisation de la Déformation et Aspects Microstructuraux, Thèse de Doctorat, ENSAM, 2001.

C. M. Chen, X. G. Jian, F. H. Sun, B. Hu, and X. S. Liu, Development of diamond-coated drills and their cutting performance, Journal of Materials Processing Technology, vol.129, issue.1-3, pp.81-85, 2002.
DOI : 10.1016/S0924-0136(02)00580-0

C. T. Childs and G. W. Rowe, Physics in metal cutting, Reports on Progress in Physics, vol.36, issue.3, pp.223-288, 1973.
DOI : 10.1088/0034-4885/36/3/001

T. H. Chil_89, M. Childs, and . Mahdi, On the stress distribution between the chip and tool during metal turning, Annals of the CIRP, vol.38, pp.55-58, 1989.

C. T. Childs, Material Property Requirements for Modelling Metal Machining, S. XXI-XXXVI, 1997.
DOI : 10.1051/jp4:1997301

URL : https://hal.archives-ouvertes.fr/jpa-00255374

I. A. Chou_98 and M. A. Choudhury, El-Baradie, Machinability of nickel-base super alloys: a general review, Journal of Materials Processing Technology, vol.77, pp.278-284, 1998.

H. L. Cold_04, R. C. Coldwell, D. K. Dewes, N. M. Aspinwall, D. G. Renevier et al., The use of soft/lubricating coatings when dry drilling BS L168, aluminium alloy, Surface and Coatings Technology, vol.177, pp.178-716, 2004.

M. B. Dasi_99, J. Da-silva, and . Wallbank, Cutting temperature: prediction and measurement methods -a review, Journal of Materials Processing Technology, vol.88, pp.195-202, 1999.

P. A. Dear_85 and . Dearnley, Rake and flank wear mechanisms of coated and uncoated cemented carbides, Journal of Engineering Materials and Technology, vol.107, pp.68-82, 1985.

D. G. Desalvo and M. C. Shaw, Hydrodynamic Action at Chip-Tool Interface, Proceedings of the 9 th International MTDR Conference, pp.961-971, 1968.

A. Devi_04, S. Devillez, W. Lesko, and . Mozer, Cutting tool crater wear measurement with white light interferometry, 126 - Références bibliographiques, pp.56-65, 2004.

E. D. Doyl_79, J. Doyle, D. Horne, and . Tabor, Frictional Interactions Between Chip and Rake Face in Continuous Chip Formation, Proc. R. Soc. London, pp.173-187, 1979.

D. D. Dudzinski and A. Molinari, A modelling of cutting for viscoplastic materials, International Journal of Mechanical Sciences, vol.39, issue.4, pp.369-389, 1997.
DOI : 10.1016/S0020-7403(96)00043-4

R. M. Elza_87, El-Zahry, On the hydrodynamic characteristics of the secondary shear zone in metal machining with sticking-sliding friction using the boundary layer theory, pp.349-359, 1987.

X. D. Fang_96, D. Fang, and . Zhang, An investigation of adhering layer formation during tool wear progression in turning of free-cutting stainless steel, Wear, vol.197, issue.1-2, pp.169-178, 1996.
DOI : 10.1016/0043-1648(96)06924-4

H. O. Geko_02, S. V. Gekonde, and . Subramanian, Tribology of tool?chip interface and tool wear mechanisms, Surface and Coatings Technology, vol.149, pp.151-160, 2002.

F. Giro_02, . Girot, and . Géhin, Perçage à sec des alliages d'aluminium aéronautique, Mécanique & Industries, vol.3, pp.301-313, 2002.

W. Grze_00 and . Grzesik, The influence of thin hard coatings on frictional behaviour in the orthogonal cutting process, Tribology International, pp.131-140, 2000.

W. Grze_02 and . Grzesik, Friction behaviour of heat isolating coatings in machining: mechanical, thermal and energy-based considerations, International Journal of Machine Tools & Manufacture, vol.43, pp.145-150, 2003.

W. Grze_99 and . Grzesik, Experimental investigation of the cutting temperature when turning with coated indexable inserts, International Journal of Machine Tools & Manufacture, vol.39, pp.355-391, 1999.

Y. B. Guo_03 and . Guo, An integral method to determine the mechanical behavior of materials in metal cutting, Journal of Materials Processing Technology, vol.142, pp.72-81, 2003.

D. M. Haan_97, S. A. Haan, W. W. Batzer, J. W. Olson, and . Sutherland, An experimental study of cutting fluid effects in drilling, Journal of Materials Processing Technology, vol.71, issue.2, pp.305-313, 1997.
DOI : 10.1016/S0924-0136(97)00089-7

K. Hosh_68, T. Hoshi, and . Hoshi, On the Metal-Cutting Mechanism with the Built-Up Edge, Proceedings of the 9 th International Machine Tool design Research Conference, pp.1099-1111, 1968.

P. S. Jack_82, P. K. Jackson, and . Wright, Application of Plastic Boundary Layer Theory to Metal Machining, Trans. ASME Journal of Engineering for Industry, vol.104, pp.358-362, 1982.

S. P. Jasp_02, J. H. Jaspers, and . Dautzenberg, Material Behaviour in Metal Cutting: Strains, Strain Rates and Temperatures in Chip Formation, Journal of Materials Processing Technology, vol.121, pp.123-135, 2002.

J. A. Jawaid, S. Sharif, and S. , Evaluation of wear mechanisms of coated carbide tools when face milling titanium alloy, Journal of Materials Processing Technology, vol.99, issue.1-3, pp.266-274, 2000.
DOI : 10.1016/S0924-0136(99)00438-0

J. A. Jawaid, S. Koksal, and S. Sharif, Cutting performance and wear characteristics of PVD coated and uncoated carbide tools in face milling Inconel 718 aerospace alloy, Journal of Materials Processing Technology, vol.116, issue.1, pp.2-9, 2001.
DOI : 10.1016/S0924-0136(01)00850-0

I. S. Jawa_93, C. A. Jawahir, and . Van-luttervelt, Recent developments in chip control research and applications, Annals of the CIRP, vol.42, pp.659-693, 1993.

J. F. Kell_02 and M. G. Kelly, Minimal lubrication machining of aluminium alloys, Journal of Materials Processing Technology, vol.120, issue.1-3, pp.327-334, 2002.
DOI : 10.1016/S0924-0136(01)01126-8

J. Kim_95, V. R. Kim, and . Marinov, Material Characterization in the Chip-Tool Deformation Zone: an Application of Boundary-Layer Theory, International Journal of Mechanical Sciences, vol.37, pp.91-95, 1995.

J. Kim1_97, Y. Kim, and . Kang, High-speed machining of aluminium using diamond endmills, International Journal of Machine Tools and Manufacture, vol.37, pp.1155-1165, 1997.

J. Kim2_97, V. R. Kim, D. Marinov, and . Kim, Built-Up Edge Analysis of Orthogonal Cutting by the Visco-Plastic Finite-Element Method, Journal of Materials Processing Technology, vol.71, pp.367-372, 1997.

K. Kish_74, H. Kishi, and . Eda, Behavior of built-up edge of aluminium alloys in contained secondary phase grain particle, th Japan Congress on Materials Research-Metallic Material, pp.120-123, 1974.

T. Kita_97, A. Kitagawa, K. Kubo, and . Maekava, Temperatre and wezr of cutting tools in highspeed machining of Inconel 718 and Ti-6Al-6V-2Sn, pp.142-148, 1997.

R. W. Klop_85, R. J. Klopp, T. G. Clifton, and . Shawki, Pressure-shear impact and dynamic viscoplastic response of mertals, Mechanics of Material, vol.4, pp.375-385, 1985.

R. Koma_01, Z. B. Komanduri, and . Hou, A review of the experimental techniques for measurement of heat and temperarures generated in some manufacturing processes and tribology, Tribology International, pp.653-682, 2001.

J. Kopa_01, M. Kopac, K. Korosec, and . Kuzman, Determination of flow stress properties of machinable materials with help of simple compression and orthogonal machining test, International Journal of Machine Tools & Manufacture, vol.41, pp.1275-1282, 2001.

R. K. Koun_01, W. J. Kountanya, and . Endres, A High-Magbification Experimental Study of Orthogonal Cutting with Edge-Honed Tools, ASME International Mechanical Engineering Congress and Exposition, pp.1-8, 2001.

E. H. Lee_51, B. W. Lee, and . Shaffer, The theory of plasticity applied to the problem of machining, Journal of Applied Physics, vol.18, pp.405-413, 1951.

L. C. Lee_95, X. D. Lee, K. Y. Liu, and . Lam, Determination of Stress Distribution on the Tool Rake Face using a Composite Tool, International Journal of Machine Tools and Manufacture, vol.35, pp.373-382, 1995.

L. S. Lei, Y. C. Shin, and F. P. Incropera, Material Constitutive Modeling Under High Strain Rates and Temperatures Through Orthogonal Machining Tests, Journal of Manufacturing Science and Engineering, vol.121, issue.4, pp.577-585, 1999.
DOI : 10.1115/1.2833062

J. Leop_00, G. Leopold, and . Schmidt, Challenge and problems with hybrid systems for modeling of machining operations, International Journal of Forming Processes, vol.3, pp.157-176, 2000.

X. Li_02 and . Li, A brief review: acoustic emission method for tool wear monitoring during turning, International Journal of Machine Tools & Manufacture, vol.42, pp.157-165, 2002.

L. X. Li, Development of a predictive model for stress distributions at the tool-chip interface in machining, Journal of Materials Processing Technology, vol.63, issue.1-3, pp.169-174, 1997.
DOI : 10.1016/S0924-0136(96)02619-2

Z. Lin_97, . Lin, . S-p, and . Lo, A study of the tool-chip interface contact problem under low cutting velocity with an elastic cutting tool, Journal of Material Processing Technology, vol.70, pp.34-46, 1997.

K. Liu_01, X. P. Liu, and . Li, Ductile cutting of tungsten carbide, Journal of Materials Processing Technology, vol.113, pp.348-354, 2001.

T. Macg_01, J. Macginley, and . Monaghan, Modelling the orthogonal machining process using coated cemented carbide cutting tool, Journal of Materials Processing Technology, vol.118, pp.293-300, 2001.

V. Madh_02, S. Madhavan, T. N. Chandrasekar, and . Farris, Direct Observations of the Chip- Tool Interface in the Low Speed Cutting of Pure Metals, Transactions of the ASME Journal of Tribology, vol.124, pp.617-626, 2002.

V. R. Mari_96 and . Marinov, On viscous fluid similarity in metal cutting (an overview), Proceedings of the 26 th International Conference of Production Engineering, 17-20 septembre, 1996.

V. R. Mari_01 and . Marinov, Hybrid analytical}numerical solution for the shear angle in orthogonal metal cutting Part I: theoretical foundation, International Journal of Mechanical Sciences, vol.43, pp.399-414, 2001.

T. D. Maru_95, M. Marusich, and . Ortiz, Modeling and Simulation of High Speed Machining, International Journal for Numerical Methods in Engineering, vol.38, pp.3675-3694, 1995.

M. E. Merchant, Mechanics of the Metal Cutting Process. I. Orthogonal Cutting and a Type 2 Chip, Journal of Applied Physics, vol.16, issue.5, pp.267-275, 1945.
DOI : 10.1063/1.1707586

E. Merc2_45 and . Merchant, Mechanics of the metal cutting process. Orthogonal cutting, Journal Applied Physics, pp.318-324, 1945.

A. Moli_02, M. Molinari, and . Nouari, Modeling of tool wear by diffusion in metal cutting, pp.135-149, 2002.

A. Mouf_98, A. Moufki, D. Molinari, and . Dudzinski, Modelling of orthogonal cutting with a temperature dependent friction law, Journal of Mechanical Physics of Solids, vol.46, pp.2103-2138, 1998.

A. Mouf_02, A. Moufki, D. Devillez, A. Dudzinski, and . Molinari, Thermomecaical Modeling of Cutting and Experimental Validation, dans Metal Cutting and High Speed Machining édité par, pp.51-67, 2002.

M. Sao, R. M. Saoubi, and H. Chandrasekaran, Investigation of the effects of tool microgeometry and coating on tool temperature during orthogonal turning of quenched and tempered steel, International Journal of Machine Tools & Manufacture, vol.44, pp.213-224, 2004.

Y. Nahe_77, E. M. Naherheim, and . Trent, Diffusion wear of cemented carbide tools when cutting steel at high speeds, Metal Technology, pp.548-555, 1977.

T. Obik_97, T. Obikawa, T. Matsumura, E. Shirakashi, and . Usui, Wear characteristic of Alumina coated ceramic tools, Journal of Materials Processing Technology, vol.63, pp.211-216, 1997.

J. G. Oldr_47 and . Oldroy, Two-Dimensional Plastic Flow of a Bingham Solid: a Plastic Boundary Layer Theory for Slow Motion, Proceedings of the Cambridge Philosophical Society, vol.43, pp.383-395, 1947.

P. L. Oxle_66 and . Oxley, Introducing strain rate dependent work material, properties into the analysis of orthogonal cutting, Annals of the CIRP, vol.13, pp.127-138, 1966.

. P. Oxle_89 and . Oxley, Mechanics of Machining: An Analytical Approach to Assessing Machinability, Journal of Applied Mechanics, vol.57, issue.1, 1989.
DOI : 10.1115/1.2888318

T. Ozel_03 and . Özel, Modeling of hard part machining: effect of insert edge preparation in CBN cutting tools, Journal of Materials Processing Technology, vol.141, issue.2, pp.284-293, 2003.
DOI : 10.1016/S0924-0136(03)00278-4

L. N. Payt_01, J. T. Payton, and . Black, Orthogonal Machining of Copper with a Hardness Gradient, Transaction of the North American Manufacturing Research Institute, pp.243-250, 2001.

Y. K. Potd_04, A. T. Potdar, and . Zehnder, Temperature and Deformation Measurements in Transient Metal Cutting, Experimental Mechanics, vol.44, pp.1-9, 2004.

H. S. Qi_00, B. Qi, and . Mills, Formation of a transfer layer at the tool-chip interface during machining, pp.136-147, 2000.

H. S. Qi_03, B. Qi, and . Mills, Modelling of the dynamic tool-chip interface in metal cutting, Journal of Materials Processing Technology, vol.138, pp.201-207, 2003.

H. S. Qi_96, B. Qi, and . Mills, On the formation mechanism of adherent layers on cutting tool, pp.192-196, 1996.

R. S. Raman, A. Longstreet, and D. Guha, A fractal view of tool???chip interfacial friction in machining, Wear, vol.253, issue.11-12, pp.1111-1120, 2002.
DOI : 10.1016/S0043-1648(02)00238-7

R. J. Rech, A. Kusiak, and J. Battaglia, Tribological and thermal functions of cutting tool coatings, 130 - Références bibliographiques, pp.364-371, 2004.
DOI : 10.1016/j.surfcoat.2003.11.027

J. L. Robi_75 and . Robinson, The mechanics of wave formation in impact welding, Philosophical. Magazine, vol.31, pp.587-597, 1975.

W. K. Rule_98, S. E. Rule, and . Jones, A REVISED FORM FOR THE JOHNSON???COOK STRENGTH MODEL, International Journal of Impact Engineering, vol.21, issue.8, pp.609-624, 1998.
DOI : 10.1016/S0734-743X(97)00081-X

R. A. Rusinek, Modélisation thermoviscoplastique d'une nuance de tôle d'acier aux grandes vitesses de déformation. Etude expérimentale et numérique du cisaillement, de la traction et de la perforation, Thèse de Doctorat, 2000.

M. Shat_01, C. Shatla, T. Kerk, and . Altan, Process modeling in machining. Part I: determination of flow stress data, International Journal of Machine Tools & Manufacture, vol.41, pp.1511-1534, 2001.

C. Spaa_71 and . Spaans, The Fundamentals of Three-Dimensional Chip Curl, Chip Breaking and Chip Control, Thèse de Doctorat, 1971.

D. A. Step_92, A. Stephenson, and . Ali, Tool temperature in interrupted metal cutting, Journal of Engineering for Industry Transaction of the ASME, vol.114, pp.127-136, 1992.

M. G. Stev_70, P. L. Stevenson, and . Oxley, An Experimental Investigation of the Influence of Speed and Scale on the Strain-Rate in a Zone of Intense Plastic Deformation, Proc. Instn. Mech. Engrs, vol.184, pp.561-569, 1969.

M. G. Stev_74 and . Stevenson, Stress-Strain Data for Predictions in Machining, Institute of Physics Conf. Ser. No. 21, pp.393-403, 1974.

G. Subb_02, W. Subhash, and . Zhang, Investigation of the overall friction coefficient in singlepass scratch test, pp.123-134, 2002.

G. Sutt_03, L. Sutter, A. Faure, N. Molinari, V. Ranc et al., An experimental technique for the measurement of temperature fields for the orthogonal cutting in high speed machining, International Journal of Machine Tools & Manufacture, vol.43, pp.671-678, 2003.

H. Take_63, T. Takeyama, and . Murata, Basic investigations on tool wear, Journal of Engineering for Industry, Transaction of the ASME, pp.33-38, 1963.

A. O. Tay_76, M. G. Tay, G. Stevenson, P. L. De-vahl-davis, and . Oxley, A Numerical Method for Calculating Temperature Distributions in machining, from Force and Shear angle Measurements, International Journal of Machine Tool Design and Research, vol.16, pp.335-349, 1976.

H. K. Tons_98, A. Tonshoff, C. Mohlfeld, J. Gey, and . Winkler, Surface modification of cemented carbide cutting tools for improved adhesion of diamond coatings, Surface and Coatings Technology, vol.108, pp.109-543, 1998.

N. Toun_02, J. Tounsi, A. Vincenti, M. A. Otho, and . Elbestawi, From the basic mechanics of orthogonal metal cutting toward the identification of the constitutive equation, International Journal of Machine Tools & Manufacture, vol.42, pp.1373-1383, 2002.

E. M. Tren_52, M. Trent, and . Met, Some factors affecting wear on cemented carbide tools, Institution of Mechanical Engineers, vol.1, pp.64-75, 1952.

E. M. Tren_63 and . Trent, Cutting steel and iron with cemented carbide tools, Part II: Conditions of seizure at the tool-work interface, Journal of the Iron and Steel Institute, pp.923-932, 1963.

E. M. Tren1_88 and . Trent, Metal Cutting and the Tribology of Seizure: I Seizure in Metal Cutting, pp.29-45, 1988.

T. E. Trent, Metal cutting and the tribology of seizure: II movement of work material over the tool in metal cutting, Wear, vol.128, issue.1, pp.47-64, 1988.
DOI : 10.1016/0043-1648(88)90252-9

E. M. Tren3_88 and . Trent, Metal Cutting and the Tribology of Seizure: III Temperature in Metal Cutting, Wear, vol.128, pp.65-81, 1988.

E. Usui_78, A. Usui, M. Hirota, and . Masuko, Analytical Prediction of Three Dimensional Cutting Process???Part 3: Cutting Temperature and Crater Wear of Carbide Tool, Journal of Engineering for Industry, vol.100, issue.2, pp.222-228, 1978.
DOI : 10.1115/1.3439415

K. M. Vern_02, J. J. Vernaza-peña, M. Mason, and . Li, Experimental Study of the Temperature Field Generated During Orthogonal Machining of an Aluminum Alloy, Experimental Mechanics, vol.42, pp.221-229, 2004.

V. Vovk_03, G. Vovk, R. Schmitz, and . Kirchheim, Three-dimensional atom probe investigation of Co/Al thin film reaction, Microelectronic Engineering, vol.70, issue.2-4, pp.533-538, 2003.
DOI : 10.1016/S0167-9317(03)00460-X

Z. Y. Wang_00, K. P. Wang, and . Rajurkar, Cryogenic machining of hard-to-cut materials, Wear, vol.239, issue.2, pp.168-175, 2000.
DOI : 10.1016/S0043-1648(99)00361-0

W. J. Wang, C. Z. Huang, and W. G. Song, The effect of tool flank wear on the orthogonal cutting process and its practical implications, Journal of Materials Processing Technology, vol.142, issue.2, pp.338-346, 2003.
DOI : 10.1016/S0924-0136(03)00604-6

W. P. Wright, J. G. Horne, and D. Tabor, Boundary conditions at the chip-tool interface in machining: Comparisons between seizure and sliding friction, Wear, vol.54, issue.2, pp.371-390, 1979.
DOI : 10.1016/0043-1648(79)90128-5

P. K. Wrig_82 and . Wright, Predicting the shear plane Angle in Machining from Work Material Strain-hardening Characteristics, Transactions of the ASME Journal of Engineering for Industry, vol.104, pp.285-292, 1982.

Y. R. Yousefi and Y. Ichida, A study on ultra???high-speed cutting of aluminium alloy:, Precision Engineering, vol.24, issue.4, pp.371-376, 2000.
DOI : 10.1016/S0141-6359(00)00048-9

M. Z. Zhan_01, Y. B. Zhang, H. Liu, and . Zhou, Wear mechanism maps of uncoated HSS tools drilling die-cast aluminum alloy, Tribology International, vol.34, pp.727-731, 2001.

Y. Zhen_97, J. W. Zheng, W. W. Sutherland, and . Olson, A Continuum Mechanics Model to Predict Shear Angle and Cutting Forces in Orthogonal Cutting, 132 - Références bibliographiques, pp.61-68, 1997.

K. A. Zvor_1898 and . Zvorykin, Work and stresses necessary for separation of metal chips, Proceedings of the Kharko Technological Institute, pp.1893-133