A. , F. , and V. A. Dunayevsky, Application of Stability Approach to Bit Dynamics, SPE Drilling & Completion, vol.13, issue.02, 1998.
DOI : 10.2118/30478-PA

A. , J. , and P. Skalle, Case Study : Abnormal Drillstring Wash-out and Fatigue Experienced when Drilling Hazardous Formation in Iranian Oil Field, 2003.

A. , R. , and E. Detournay, Cutting experiments in sandstones with blunt PDC cutters, Proc. EuRock 92, pp.215-220, 1992.

B. , J. R. , E. A. Biediger, V. Gupta, D. Ertas et al., Drilling Vibrations Modeling and Field Validation, p.112650, 2008.

A. D. Black, B. H. Walker, G. A. Tibbits, and J. L. Sandstrom, PDC Bit Performance for Rotary, Mud Motor, and Turbine Drilling Applications, SPE Drilling Engineering, vol.1, issue.06, p.13258, 1986.
DOI : 10.2118/13258-PA

B. , S. , S. Menand, and H. Sellami, Which Drill Pipe is the less Resistant to Buckling : Steel, Aluminum or Titanium Drill Pipe ? SPE, 2011.

B. , J. F. , T. Warren, and S. Behr, Bit whirl : A new theory of PDC bit failure. SPE 19571, Proc. 64th Annual Tech. Conf, 1989.

C. , N. , H. Sellami, E. Chenevez, and L. Gossuin, A Stick-slip Analysis Based on Rock/Bit Interaction : Theoretical and Experimental Contribution, 2000.

C. , J. B. , and W. Daniels, A study of factors influencing the drillability of shales: Single cutter experiments with stratapax drill blanks, Journal of Energy Resources Technology, vol.101, 1979.

C. , S. L. , K. Blackwood, and E. Lamine, Field Investigation of the Effects of Stick-Slip, Lateral, and Whirl Vibrations on Roller-Cone Bit Performance, 2002.

C. , R. , S. Chen, and G. Lefort, New Bit Design, Cutter Technology Extend PDC Applications to Hard Rock Drilling, pp.91840-186, 2005.

C. , C. , and T. Richard, Influence of the back and side rake angles in rock cutting, 2005.

D. , E. , and C. Atkinson, Influence of pore pressure on the drilling response in lowpermeability shear-dilatant rocks, Int. J. Rock Mech, & Mining Sc, vol.37, pp.1091-1101, 2000.

D. , E. , and P. Defourny, A phenomenological model of the drilling action of drag bits, 1992.

D. , E. , and A. Drescher, Plastic flow regimes for a tool cutting a cohesive-frictional material, Numerical Models in Geomechanics, pp.367-376, 1992.

D. , E. , and C. P. Tan, Dependence of Drilling Spe-cific Energy on Bottom-Hole Pressure in Shales, 2002.

D. , G. , T. S. Klausen, A. Hendricks, and D. Pafitis, New Directions in Rotary Steerable Drilling, Oilfield Review, 2000.

D. , M. P. , and H. Henneuse, Detection and monitoring of the stick-slip motion: Field experiments, 1991.

D. , V. A. , F. Abbassian, and A. Judzis, Dynamic Stability of Drillstrings Under Fluctuating Weight on Bit, 1993.

E. Marzouki and Z. , Etude du comportement dynamique des trains de tiges de forage pétrolier, 2007.

E. , M. A. , R. L. Wells, D. W. Dareing, and K. Nagirimadugu, Effect of process damping on longitudinal vibrations in drillstrings, Journal of Energy Resources Technology, vol.116, pp.129-135, 1994.

F. , M. J. , F. Abassian, S. H. Parfitt, and A. Mcclean, The Destruction of PDC Bits by Severe Slip-Stick Vibration, 1997.

G. , L. , S. Menand, and H. Sellami, PDC Bits : All Comes From The Cutter/Rock Interaction, 2006.
URL : https://hal.archives-ouvertes.fr/hal-00585922

G. , Y. , and J. Fortin, Mécanique des roches en géologie : des processus microscopiques au comportement macroscopique, Colloque "Microstructure et Propriétés des Matériaux Presse des Ponts et Chaussées, 2005.

H. G. , A. Kyllingstad, and A. Kylling, Torque feedback used to cure slip-stick motion, 63rd SPE annual technical conference and exhibition, pp.277-282, 1988.

H. , J. E. Lubinski, and A. , Cumulative Fatigue Damage of Drill Pipe in Dog-Legs, 1966.

H. , R. R. , and R. P. Behringer, Logarithmic rate dependence of force networks in sheared granular materials, Nature, vol.421, pp.928-931, 2003.

H. , G. , and M. Neubert, Lateral Drillstring Vibrations in Extended-Reach Wells, 2000.

H. , T. H. , P. V. Seshadri, and K. S. Durham, A Unified Approach to Drillstem-Failure Prevention, p.22002, 1992.

H. , D. , C. Veje, and R. P. Behringer, Stress fluctuations in a 2D granular Couette experiment : A continuous transition, Phys. Rev. Lett, vol.82, pp.5241-5244, 1999.

J. , A. , S. Upadhaya, and A. R. Chowdhury, Successful PDC/RSS Vibration Management Using Innovative Depth-of-Cut Control Technology : Panna Field, Offshore India, p.104388, 2007.

J. , A. , R. G. Bland, D. A. Curry, A. D. Black et al., Optimization of Deep Drilling Performance; Benchmark Testing Drives ROP Im-provements for Bits and Drilling Fluids, 2007.

K. , M. , Y. L. Abdel-magid, and B. Balachandran, Drill-string Torsional Vibration Suppression Using GA Optimized Controllers, Journal of Canadian Petroleum Technology, vol.48, issue.12, 2009.

K. , W. Savignat, and J. , Soft Torque MkII performance in well MA-10, pp.2001-5469, 2001.

K. , K. H. , H. Hughes-jones, E. Chavez, K. A. Aziz et al., Case History : A Robust Point-the-Bit Rotary Steerable System with At-Bit Imaging and 3D Geosteering Service Integral to Optimal Wellbore, 2009.

K. , E. , and A. K. Wojtanowicz, An experimental study of sliding friction between PDC drill cutters and rocks, Int. J. Rock Mech. Min. Sc. & Geomech. Abstr, vol.32, issue.3, pp.277-283, 1995.

K. , H. , A. Kyllingstad, and M. M. Moe, Operational Experience With Use of a Hex Pump on a Land Rig, 2005.

K. , A. , and P. J. Nessjoen, A New Stick-Slip Prevention System, SPE/IADC, pp.119660-188, 2009.

L. Iii and L. W. , PFC Modeling of Rock Cutting Under High Pressure Conditions In Rock Mechanics: Meeting Society's Challenges and Demands (1st Canada-U.S. Rock Mechanics Symposium, pp.511-518, 2007.

L. Iii, L. W. , O. J. Hoffmann, J. R. Jain, C. El-hakam et al., Downhole Vibration Measurement, Monitoring and Modeling Reveal Stick-Slip as a Primary Cause of PDC Bit Damage in Today's Applications, 2010.

L. , R. I. , D. H. Van-campen, and W. J. Keultjes, Stick-slip whirl interaction in drillstring dynamics, Journal of Vibration and Acoustics, vol.124, pp.209-220, 2002.

M. , M. M. , and D. K. Tanaka, Consideration of Stribeck Diagram Parameters in the Investigation on Wear and Friction Behavior in Lubricated Sliding, J. of the Braz. Soc. of Mech. Sci. & Eng, vol.1, 2007.

A. Muszynska, Free, forced and self-excited vibrations, Orbit, 1997.

P. , P. , E. Sullivan, and T. Harris, Development and Utilization of a Bit-Based Data- Acquisition System in Hard-Rock PDC Applications, 2007.

P. , D. R. , and J. P. Desplans, Application of high sampling rate downhole measurements for analysis and cure of stick-slip in drilling, 1994.

R. , T. , E. Detournay, A. Drescher, P. Nicodeme et al., The scratch test as a means to measure strength of sedimentary rocks, 1998.

R. , T. G. , C. Soize, and R. Sampaio, Full Steam Ahead Rigzone Q1 2010 Land Rig Review Non-linear dynamics of a drillstring with uncertain model of the bit-rock interaction, RIGZONE Int. J. Non-linear Mech, vol.44, issue.8, pp.865-876, 2009.

R. E. , J. A. Hood, and J. D. Macpherson, Analysis of the Stick-Slip Phenomenon Using Downhole Drillstring rotation data, 1999.

S. , H. , C. Fairhurst, E. Deliac, and B. Delbast, The role of in situ stresses and mud pressure on the penetration rate of PDC bits, Proceedings of the International Symposium on Rock at Great Depth, 1989.

S. H. and P. Cordelier, Calcul d'un outil PDC en forage pétrolier profond -logiciel de simulation DRILSIM 3D, 1991.

S. , A. F. , M. J. Van-de-molengraft, J. J. Kok, L. Van et al., H1 control for suppressing stick-slip in oil well drillstrings, IEEE Control Syst, pp.19-30, 1998.

S. , C. , D. Goyallon, J. Poloce, H. Sellami et al., Drilling Without WOB, Dream or Reality ? An Effective Field Test by Total Angola, 2007.
URL : https://hal.archives-ouvertes.fr/hal-00749074

S. , J. , and L. Jezequel, Mode coupling instability in friction-induced vibrations and its dependency on system parameters including damping, Eur. Journ. Of Mech. A/Solids, vol.26, pp.106-122, 2006.
URL : https://hal.archives-ouvertes.fr/hal-00207759

S. , J. R. , J. B. Lund, and R. K. Galloway, Friction on PDC Cutters at High Normal Stress, Transactions of the ASME, vol.124, 2002.

S. , S. F. , F. E. Dupriest, J. R. Bailey, and L. Wang, Roller Reamers Improve Drilling Performance in Wells Limited by Bit and Bottomhole Assembly Vibrations, 2009.

S. P. , A. M. Chevalier, and N. P. Politis, Nonlinear Stochastic Drill-String Vibrations, Transactions of the ASME, vol.124, 2002.

S. Olberg, T. , H. Laastad, B. Lesso, and A. Newton, The Utilization of the Massive Amount of Real-Time Data Acquired in Wired Drillpipe Operations, 2008.

T. , M. , A. Murdock, and D. Jelley, Rotary Drag-Type Drill Bits and Methods of Designing Such Bits. United States Patent, Pub. No. US, pp.20551-20552, 2001.

T. , E. , A. Weber, D. Crowell, and Z. Nagy, Evaluating the True Cost of Losing a Bottomhole Assembly, 2008.

T. , R. W. , and C. Wang, An integrated model for drill-string dynamics, Journal Of Sound and Vibration, vol.224, issue.1, pp.123-165, 1999.

V. , O. , O. Vincke, G. Perrin, J. P. Sarda et al., Fatigue of Drillstring : State of the Art, Oil & Gas Science and Technology ? Rev. IFP, vol.57, issue.1, pp.7-37, 2002.

. Van-den and L. Steen, Suppressing stick-slip-induced drillstring oscillations: a hyperstability approach, 1997.

W. , J. Warren, T. M. , J. F. Brett, and S. L. Allen, Closing in on stick-slip. http://www.miningaustralia.com.au/news/closing-in-on- stick-slip Development of a whirl-resistant bit, SPE, 1990.

W. , T. M. , and J. H. Oster, Torsional Resonance of Drill Collars with PDC Bits in Hard Rock, 1998.

W. , G. E. , and R. I. Clayton, A New PDC Cutting Structure Improves Bit Stabilization and Extends Application Into Harder Rock Types, 1993.

W. , X. , C. Y. Wang, H. Yuan, and Z. H. Xie, Study on Fracture Mechanism of Rock Cutting, Key Engineering Materials, vol.250, pp.200-208, 2003.

W. , A. K. , and E. Kuru, Mathematical Modeling of PDC Bit Drilling Process Based on a Single-Cutter Mechanics, Journal of Energy Resources Technology, vol.115, pp.247-256, 1993.

X. Wu, S. , L. Paez, U. Partin, and M. Agnihotri, Decoupling Stick/Slip and Whirl To Achieve Breakthrough in Drilling Performance, IADC/SPE Drilling Conference and Exhibition, 2010.
DOI : 10.2118/128767-MS

Y. , A. S. , and A. P. Christoforou, Stick-Slip and Bit-Bounce Interaction in Oil-Well Drillstrings, Transactions of the ASME, vol.128, 2006.

.. De-forage, Chapitre 6

-. De-stick, Chapitre 7, p.165