Z. Pater, Finite element analysis of cross wedge rolling, Journal of Materials Processing Technology, vol.173, issue.2, pp.201-208, 2006.
DOI : 10.1016/j.jmatprotec.2005.11.027

Z. Pater, A study of cross wedge rolling process, Journal of Materials Processing Technology, vol.80, issue.81, pp.370-375, 1998.
DOI : 10.1016/S0924-0136(98)00193-9

M. Hayama, Estimation of load and contact width in rotational compression of rods

Y. F. Qiang and P. B. Song, Analysis on temperature distribution in cross wedge rolling process with finite element method, J. Mater. Process. Tech, vol.188, pp.392-396, 2007.

G. Liu, Z. Zhong, and Z. Shen, Influence of Reduction Distribution on Internal Defects During Cross-wedge-rolling process, Procedia Engineering, vol.81, pp.263-267, 2014.
DOI : 10.1016/j.proeng.2014.09.161

B. Wang, A simulation of roll wear in hot rolling processes, 1996.

W. Weroñski and Z. Pater, Selection of geometric parameters of transverse wedge rolling tools, Journal of Materials Processing Technology, vol.34, issue.1-4
DOI : 10.1016/0924-0136(92)90117-B

A. Bozgeyik, Computer aided evaluation of cross wedge rolling parameters, 2006.

J. Zhou, Y. Yu, and Q. Zeng, Analysis and experimental studies of internal voids in multi-wedge cross wedge rolling stepped shaft, The International Journal of Advanced Manufacturing Technology, vol.10, issue.2, pp.9-12, 2014.
DOI : 10.1016/j.proeng.2011.04.125

S. Chiluveru, Computational modeling of crack initiation in cross-roll piercing, Massachusetts Institute of Technology, 2007.

Q. Li and M. Lovell, The establishment of a failure criterion in cross wedge rolling, The International Journal of Advanced Manufacturing Technology, vol.24, issue.3-4
DOI : 10.1007/s00170-003-1607-0

P. Mangin, Identification des paramètres clés du laminage transversal : vers la formalisation des connaissances scientifiques et technologiques, École Nationale Supérieure d 'Arts et Métiers, 2012.

M. Hayama, Optimum working conditions in the cross wedge rolling of stepped shaft, J. Mech

Z. Pater, W. Weroñski, J. Kazanecki, and A. Gontarz, Study of the process stability of cross wedge rolling, Journal of Materials Processing Technology, vol.92, issue.93, pp.92-93, 1999.
DOI : 10.1016/S0924-0136(99)00229-0

Z. Pater, Tools optimisation in cross wedge rolling, Journal of Materials Processing Technology, vol.139, issue.1-3, pp.153-159, 2003.
DOI : 10.1016/S0924-0136(03)00212-7

M. L. Silva, G. H. Pires, and S. T. Button, Damage evolution during cross wedge rolling of steel DIN 38MnSiVS5, Procedia Engineering, vol.10, pp.752-757, 2011.
DOI : 10.1016/j.proeng.2011.04.125

Z. Pater, A. Tofil, J. Tomczak, and T. Bulzak, Numerical Analysis of the Cross Wedge Rolling Process ( Cwr ) for a Stepped Shaft, pp.177-180, 2015.

. Claasen and . Lorenz, Querwalzen -Möglichkeiten und Kriterien, Sächsische Fachtagung Umformtechnik, 1995.

A. Tanaka and T. Danno, Hot forming of stepped steel shafts by wedge rolling with three rolls, J

A. Tselikov, A. Tomlenov, V. Zyuzin, A. Tretyakov, and G. Nikitin, Teoriya prokatki: Spravochnik (Theory of Rolling: A Handbook), Metallurgiya

R. Neugebauer, M. Kolbe, and R. Glass, New warm forming processes to produce hollow shafts, Journal of Materials Processing Technology, vol.119, issue.1-3, pp.1-3, 2001.
DOI : 10.1016/S0924-0136(01)00939-6

M. Komura, Y. Koizumi, and K. Kobayashi, Cross wedge rolling method, Sci Mach, vol.28, issue.7, pp.23-27, 1976.

Z. Deng, M. Lovell, and K. Tagavi, Influence of Material Properties and Forming Velocity on the Interfacial Slip Characteristics of Cross Wedge Rolling, Journal of Manufacturing Science and Engineering, vol.27, issue.81, p.647, 2001.
DOI : 10.1016/S0924-0136(98)00111-3

R. Glaß, F. Hahn, M. Kolbe, and L. W. Meyer, Processes of partial bulk metal-forming?aspects of technology and FEM simulation, J. Mater. Process. Technol, pp.80-81, 1998.

A. Ghiotti, S. Fanini, S. Bruschi, and P. F. Bariani, Modelling of the Mannesmann effect, CIRP Annals, vol.58, issue.1, pp.255-258, 2009.
DOI : 10.1016/j.cirp.2009.03.099

G. Fang, L. P. Lei, and P. Zeng, Three-dimensional rigid???plastic finite element simulation for the two-roll cross-wedge rolling process, Journal of Materials Processing Technology, vol.129, issue.1-3, pp.1-3, 2002.
DOI : 10.1016/S0924-0136(02)00610-6

M. Wang, X. Li, F. Du, and Y. Zheng, Hot deformation of austenite and prediction of microstructure evolution of cross-wedge rolling, Materials Science and Engineering: A, vol.379, issue.1-2, pp.133-140, 2004.
DOI : 10.1016/j.msea.2004.01.055

M. Wang, X. Li, F. Du, Y. P. Zheng-]-x, T. A. Fu et al., Theoretical method for estimation of mean pressure on contact area between rolling tools and workpiece in cross wedge rolling process Past developments, current applications and trends in the cross wedge rolling process Initial billet temperature influence and location investigation on tool wear in cross wedge rolling Contact Pressure Measurement System in Cross Wedge Rolling Development of a warm cross wedge rolling process using FEA and downsized experimental trials Analysis on temperature distribution in cross wedge rolling process with finite element method, Int. J. Mech. Sci. Int. J. Mach. Tools Manuf. Int. J. Adv. Manuf. Technol. Adv. Mater. Process. Technol. Prod. Eng. J. Mater. Process. Tech, vol.39, issue.188, pp.233-243, 1993.

C. Bibliographie, P. Gutierrez, L. Mangin, R. Langlois, ]. Bigot et al., Development of a tool design method in cross wedge rolling : description and applications Identification des paramètres clés du laminage transversal : vers la formalisation des connaissances scientifiques et technologiques École Nationale Supérieure d 'Arts et Métiers Development of a knowledge based sequence design system for cross wedge rolling Fuzzy sets Introduction à la logique floue, Fundamentals of Fuzzy Logic Control ? Fuzzy Sets , Fuzzy Rules and Defuzzifications Advanced Fuzzy Logic Technologies in Industrial Applications, pp.611-612, 1965.

A. Tselikov, A. Tomlenov, V. Zyuzin, A. Tretyakov, and G. Nikitin, Teoriya prokatki: Spravochnik (Theory of Rolling: A Handbook) Past developments, current applications and trends in the cross wedge rolling process, Metallurgiya. Int. J. Mach. Tools Manuf, vol.33, issue.3, pp.367-400, 1993.

W. Weroñski and Z. Pater, Selection of geometric parameters of transverse wedge rolling tools, Journal of Materials Processing Technology, vol.34, issue.1-4
DOI : 10.1016/0924-0136(92)90117-B

. Claasen and . Lorenz, Querwalzen -Möglichkeiten und Kriterien, Sächsische Fachtagung Umformtechnik, 1995.

M. L. Silva, G. H. Pires, and S. T. Button, Damage evolution during cross wedge rolling of steel DIN 38MnSiVS5, Procedia Engineering, vol.10, pp.752-757, 2011.
DOI : 10.1016/j.proeng.2011.04.125
URL : https://doi.org/10.1016/j.proeng.2011.04.125

M. Latham and D. Cockroft, Ductility and the workability of metals, J. Inst. Met, vol.96, issue.11, p.168

M. Oyane, T. Sato, K. Okimoto, and S. Shima, Criteria for ductile fracture and their applications, Journal of Mechanical Working Technology, vol.4, issue.1, pp.65-81, 1980.
DOI : 10.1016/0378-3804(80)90006-6

M. F. Novella, A. Ghiotti, and S. Bruschi, Effect of the Zener-Hollomon parameter on the formability of AA6082-T6 formed at elevated temperature, AIP Conf. Proc, vol.1769, 2016.
DOI : 10.1016/j.jmatprotec.2015.01.030

J. Rice and D. Tracey, Computational Fracture Mechanics, Numer. Comput. Methods Struct. Mech, vol.1, pp.585-623, 1973.
DOI : 10.1016/B978-0-12-253250-4.50031-2

L. Défauts-À, Analyse des instabilités du procédé, p.171

.. Conséquences-de-l-'usure, Evolution progressive de l'usure, p.225

]. R. Carnes, G. Maddock, R. Lévêque, S. Polat, S. Atapek et al., Tool Steel Selection Etude du frottement et de l'usure d'acier à outils à travail à chaud Institut National Polytechnique de Toulouse Données numériques sur les aciers inoxydables Endommagement des outillages de forgeage traités par nitruration : Etude et modélisation Institut national des sciences appliquées de Toulouse Wear behaviour of heat treated hot work tool steels under dry sliding conditions Nitruration, nitrocarburation et dérivés, Bibliographie [1] AZOMaterials, pp.37-40, 1979.

B. Wang, X. Zhao, W. Li, M. Qin, and J. Gu, Effect of nitrided-layer microstructure control on wear behaviour of AISI H13 hot work die steel, Appl. Surf. Sci, pp.3-7, 2017.

M. Wang, D. Xiang, C. Xiao, J. Zhou, and Z. Jia, Influence of cooling condition of tools on central deformation of workpiece and tool wear in cross wedge rolling, The International Journal of Advanced Manufacturing Technology, vol.191, issue.131, pp.5-8, 2012.
DOI : 10.1016/j.surfcoat.2004.04.053

S. Mridha and D. H. Jack, Etching techniques for nitrided irons and steels, Metallography, vol.15, issue.2, pp.163-175, 1982.
DOI : 10.1016/0026-0800(82)90020-9

J. Zhou, C. Xiao, Y. Yu, and Z. Jia, Influence of tool parameters on tool wear in two-roll crosswedge rolling, Int. J. Adv. Manuf. Technol, vol.65, pp.5-8, 2013.

H. Huang, X. Chen, B. Fan, Y. Jin, and X. Shu, Initial billet temperature influence and location investigation on tool wear in cross wedge rolling, The International Journal of Advanced Manufacturing Technology, vol.18, issue.81, pp.9-12, 2015.
DOI : 10.1016/S0924-0136(98)00111-3

M. Pillet, Six Sigma comment l'appliquer
URL : https://hal.archives-ouvertes.fr/hal-00470000

Q. Li, M. R. Lovell, W. Slaughter, and K. Tagavi, Investigation of the morphology of internal defects in cross wedge rolling, Journal of Materials Processing Technology, vol.125, issue.126, pp.248-257, 2002.
DOI : 10.1016/S0924-0136(02)00303-5